NewNot sure which service you need? Answer four quick questions. Try the Service Finder

Design tool

Snap-fit calculator for 3D printed parts

Check whether a cantilever snap-fit will survive assembly when it is 3D printed. The calculator uses data measured on printed test bars in both directions, then accounts for print orientation, layer height, wall loops and infill, temperature, humidity and printing tolerance, so the result reflects how the part is actually built and used.

1Material and printing

Print orientation of the arm

Which orientation is my part?

Look at how the arm sits on the build plate in your slicer. The arrow shows the direction the arm bends when the hook snaps in; the white lines are the printed layers.

On its sideBends parallel to the bed. Every layer runs the full length of the arm, so the bending is carried by continuous extrusion lines.
Flat, hook upBends up and down. The arm is still made of lines along its length, but its thickness and the hook are counted in layers.
UprightBends across the layers. Each layer joint is pulled open at the root: the weakest choice.
mm
mm
×
×
%

Use your slicer's values (Bambu Studio defaults: 2 walls, 15 % infill). If the arm is thicker than the solid walls and shells, its core is infill: the arm gets softer, which the calculator includes in the forces.

2How often it is assembled
3Arm geometry
mm
mm
mm
mm
mm
mm

Same value at root and hook = straight arm. A thinner tip spreads the strain along the arm; tapering the thickness to half lets the hook deflect about 60% further for the same strain.

°
°
mm
4Mating part and conditions
°C
mm

The link in your address bar keeps your inputs, so you can bookmark or share the result.

Loading material data…

What to change

    Printing checks

      Slicer settings for the arm

        Ask an engineer to review this snap-fit

        How the calculator checks a printed snap-fit

        1. Strain at the root of the arm

        When the hook passes the mating edge, the arm bends by the undercut y. The highest strain is at the root, on the outer surface. For a straight arm of length L and thickness h:

        ε = 3 · y · h / (2 · L²)

        For tapered arms the calculator integrates the bending along the arm instead of using a fixed table value. This is the cantilever method from the Bayer (now Covestro) design guide Snap-Fit Joints for Plastics, which is the standard reference for this calculation.

        2. What the printed material can take

        Injection-moulding guides give one allowable strain per plastic. A printed part is different: it is stronger along the extrusion lines than across the layers. The calculator starts from Bambu Lab's data sheets, which test bars printed both ways, and applies the guide's rules:

        • about 70 % of the strain at the material's strength in bending,
        • never more than half the elongation at break (for brittle and fibre-filled grades),
        • across the layers, the tensile limit between layers also applies,
        • 60 % of the single-use value for joints that are opened repeatedly.

        3. Forces

        The force to deflect the hook is P = E · b · h² · ε / (6 · L). The push-on and pull-off forces add friction on the entry and retention faces:

        W = P · (μ + tan angle) / (1 − μ · tan angle)

        When μ · tan β reaches 1, the latch cannot be pulled apart at all. As the Bayer guide requires, E is a secant modulus: plastics get softer as they stretch, so the calculator follows a smooth stress-strain curve between the data-sheet modulus and bending strength. Friction is shown as a range because printed surfaces vary.

        4. How it is printed

        Dimensions built from stacked layers snap to the layer height: printed flat, a 1.5 mm arm at 0.2 mm layers is really 1.6 mm. From your wall loops, shell layers and infill the calculator draws the real cross-section. A sparse core does not change the strain on the surface (that is set by how far the arm bends), but it makes the arm softer, so the forces drop.

        5. The root corner

        The strain peaks in the inside corner where the arm meets the wall. The calculator estimates the stress concentration Kt ≈ 1 + 0.45 / √(R/h). In flat and upright prints the fillet is a staircase of layers, so it counts one layer less. The local strain Kt · ε must stay below the breaking elongation in the loaded direction. This catches sharp corners on brittle grades such as PC, silk PLA or carbon-fibre grades printed across the layers.

        6. Temperature and humidity

        Plastics soften as they warm up. In the standard heat-deflection test (ISO 75, 0.45 MPa) the HDT is reached when the bar bends 0.2 %, which means its stiffness has fallen to about 225 MPa. The calculator uses this as the end point of a curve that stays nearly flat at moderate temperature and drops steeply near the HDT. For nylons it can switch to Bambu Lab's published wet values: moisture makes nylon softer and weaker, but tougher.

        7. Tolerance and the mating part

        A printed arm can come out a little thicker and the undercut a little deeper. The calculator repeats the check at ± your printing tolerance and warns if the worst case fails. If the mating part is about as flexible as the arm, each part takes about half the deflection (Bayer guide).

        8. Preload and creep

        A good snap-fit springs back straight after assembly. If the arm stays bent to clamp something, the plastic slowly relaxes and the clamping force falls, faster when warm. The calculator compares the continuous strain with a long-term limit of 35 % of the single-use allowable strain, reduced with temperature. This limit is an IMECA3D estimate.

        Limits. This is a design check, not a guarantee. It assumes a well-calibrated printer and filament dried as specified. It does not cover fatigue over thousands of cycles, impact, or cold-temperature brittleness. The data-sheet values come from Bambu Lab's printed test bars; the temperature curve, the corner factor, the infill stiffness and the long-term limit are IMECA3D engineering estimates, set out in the data file, which will be refined with test prints on our own printers. For safety-critical or high-volume parts, test a printed prototype.

        Material data and allowable strains used
        GradeOn its side / flat, onceOn its side / flat, repeatedUpright, onceBending modulusWet modulusHDT 0.45 MPaSource

        Allowable strains at 23 °C, dry. Values from Bambu Lab Technical Data Sheets (printed specimens, 100 % infill, annealed and dried); wet nylon values from Bambu Lab's dry/wet comparison tables. Your printer, settings and filament batch will differ.

        Not in the calculator:

          New to snap-fits? Read our guide to snap-fit design for 3D printing, or compare materials with the Material Selector.

          Want an engineer to check the whole joint?

          Send us the CAD file. We check the snap-fits, wall thickness, tolerances and print orientation before anything is printed.

          Ask for a Design Review
          Chat on WhatsApp