NewNot sure which service you need? Answer four quick questions. Try the Service Finder

Design tool

Spur gear generator for 3D printing

Design a pair of involute spur gears that mesh properly when they are 3D printed. Set the module and teeth, see the pair turning, check the tooth strength with real printed-material data, and download the gears as STEP or DXF for CAD, or STL for your slicer.

1Gear pair
mm
#
#
× m
× m

mm

For FDM with a 0.4 mm nozzle, a module of 1 or more prints clean teeth; 1.5–2 is a robust choice. Gear 1 is the driver. Pressure angle: 20° is standard; 25° gives stronger teeth; 14.5° only to match existing gears.

2Printing
mm
mm

The clearance is taken off the teeth (half on each gear), so the gears still fit the theoretical centre distance. 0.1–0.2 mm suits a well-tuned printer.

mm
mm
mm
mm

Printed holes usually come out 0.1–0.2 mm small. Enter the size you want in CAD, then test-fit and adjust.

3Load and use
N·m
rpm
°C

Don't know the torque? A small hobby servo gives about 0.2–1 N·m; check your motor's data sheet. 1 kgf·cm ≈ 0.098 N·m.

The link in your address bar keeps your inputs, so you can bookmark or share the design.

Loading material data…

Download

Gear 1
Gear 2
Both, meshed

Files are made in your browser; nothing is uploaded. All in millimetres. STEP is a solid with exact involute flanks for SolidWorks, Fusion, Onshape or FreeCAD; STL goes straight to the slicer; DXF is the 2D outline.

Design checks

    Printing the gears

      Ask an engineer to design your gear train

      How the generator designs a printable gear pair

      1. Involute teeth

      The teeth follow the involute curve of the ISO 53 standard rack: addendum 1 × module, dedendum 1.25 × module. Involute teeth roll against each other at a constant speed ratio, even if the centre distance is slightly off, which suits printed parts.

      pitch diameter d = m · z   ·   centre distance a = m (z₁ + z₂) / 2

      2. Profile shift

      Small gears (fewer than about 17 teeth at 20°) get undercut at the root. A positive profile shift moves the tooth outwards to avoid it. The generator computes the working pressure angle and the new centre distance, and shortens the tips if needed so the gears do not touch the opposite root.

      3. Print clearance

      Printed teeth are slightly fatter than designed and the surfaces are rough. The clearance you enter is taken off the tooth thickness, half on each gear, so the pair turns freely at the theoretical centre distance.

      4. Tooth strength

      The tooth is treated as a short beam loaded at its tip (Lewis equation), with a speed factor for rough profiles:

      σ = Kv · Ft / (b · m · Y)

      Y is the Lewis form factor for the number of teeth. The result is compared with the bending strength of flat-printed Bambu Lab test bars, reduced for the duty: 50 % when turned by hand, 30 % for short motor runs, 15 % for continuous running.

      5. Why continuous running is so strict

      Printed gears that run for a long time fail by heat and fatigue, not by a single overload. In tests at ZHAW on printed gears run to the VDI 2736 method, ABS teeth broke at about 16 MPa root stress, nylon survived 2 million cycles at 12 MPa, and PLA melted. The 15 % factor keeps the stress in that range.

      6. Downloads

      The STEP file is a real solid, not a mesh: the flanks are smooth curves and the bore is a true cylinder, so in Fusion, SolidWorks, Onshape or FreeCAD you can add hubs, spokes, keyways or set screws directly. The STL goes straight to the slicer (millimetres, flat), and the DXF is the 2D outline. Everything is generated in your browser.

      Limits. This is a design aid for external spur gears, not a full gear standard calculation. It does not model the true undercut shape, tooth wear, flank pressure (pitting), heat build-up or shaft deflection, and the duty factors are IMECA3D estimates. Gears for safety-critical or high-power drives need a full calculation (for plastic gears, VDI 2736) and testing.

      More tools: the snap-fit calculator, the Material Selector, or all our design tools.

      Need gears inside a real product?

      Send us the requirements or a sketch. We design the gear train, the housing and the shafts, and print and test the parts.

      Ask for a Design Review
      Chat on WhatsApp